Redmax HEZ2500S Bedienungsanleitung Seite 1

OWNER/OPERATOR MANUALSTICK EDGERST3106-93110(007)HEZ2500SThe engine exhaust from this productcontains chemicals known to the Stateof California to ca

❲10❳ BEFORE STARTING THE ENGINE1. The area within a perimeter of 50 feet (15m) ofthe person using the product should beconsidered a hazardous area in

Never place the throttle into the high speedposition when starting the engine.3. After starting the engine, check to make surethat the cutting attachm

❲12❳• IF SOMEONE COMES1. Guard against hazardous situations at all times.Warn adults to keep pets and children awayfrom the area. Be careful if you ar

5. For safe operation HANDLING FUEL1. The engine of the RedMax product is designedto run on a mixed fuel which contains highlyflammable gasoline. Nev

❲14❳SE4 MOUNTING ENGINE (SE1)1. Push the driveshaft housing toward the clutchhousing and rotate it by hand to check that thedriveshaft is engaged wit

6. Set upSE5SE6SE73.Place the blade between the cutter holders (A)and (B) while locking the gear shaft by puttingthe bar, one of the tools provided, t

❲16❳• Gasoline is very flammable. Avoid smokingor bringing any flame or sparks near fuel.Make sure to stop the engine and allow itcool before refueli

container to avoid mixing up with gasoline orother containers.6. Indicate the contents on outside of container foreasy identification. FUELING THE U

❲18❳8. OperationOP3OP1OP2(1)(2)(3)OP4The RedMax stick edger Model HEZ2500S isdesigned for edging lawn in gardens, parks,roadsides and so on. Before st

8. Operation❲19❳rope quickly until engine fires. (OP6)(1) choke lever (2) close (3) open(4) ignition switch (5) start (6) stop(7) throttle set but

❲20❳8. Operation ADJUSTING IDLING SPEED (OP8)1. When the engine tends stop frequently at idlingmode, turn the adjusting screw clockwise.2. When the c

9. Maintenance❲21❳ BE SURE TO CHECK THE FOLLOWING BEFORE USING YOUR STICK EDGERItem to be checked Response1Edging mechanism• See if attachment is loo

❲22❳• Make sure that the engine has stopped and iscool before performing any service to themachine. Contact with moving cutting heador hot muffler may

(1)(2)MA5 MUFFLER• Inspect periodically, the muffler for loosefasteners, any damage or corrosion. If any signof exhaust leakage is found, stop using

❲24❳9. Maintenanceedger. Note that it is necessary to remove theengine cover shown in (MA5) in order to be ableto view the upper part of the cylinder.

10. Storage• Aged fuel is one of major causes of enginestarting failure. Before storing the unit, empty thefuel tank and run the engine until it uses

❲26❳11. Troubleshooting guideCase 1. Starting failure CHECK PROBABLE CAUSES ACTIONfuel tank ➞ incorrect fuel ➞ drain it and with correct fuelfuel filt

12. Parts list NOTE : 1. Use KOMATSU ZENOAH genuine parts as specified in the parts list for repair and/orreplacement. 2. KOMATSU ZENOAH does not warr

12. Parts list ❲28❳Fig.1 DRIVE UNIT HEZ2500S (S/N 000000 and up)

Fig.1 DRIVE UNIT HEZ2500S (S/N 000000 and up)Key# Description Part Number Q'ty1 PIPE-COMP T3052-12100 12 SHAFT 3520-12212 13 GEARCASE-ASS’Y 6367

SAFETY FIRSTInstructions contained in warnings within thismanual marked with a symbol concerncritical points which must be taken intoconsideration to

Fig.2 ENGINE UNIT HEZ2500S (S/N 015257 and up)❲30❳12. Parts list

Fig.2 ENGINE UNIT HEZ2500S (S/N 015257 and up)❲31❳Key# Description Part Number Q'ty1 CYLINDER 4810-12111 12 GASKET, base 4810-12210 13 BOLT 1850

The California Air Resources Board and KOMATSU ZENOAH are pleased to explain theemission control system warranty on your 1995 and later small off-road

KOMATSU ZENOAH AMERICA INC. 4344 Shackleford Road Suite 500 Norcross, Georgia 30093 EMISSION-RELATED PARTS, FOR TWO (2) YEARS FROM THE DATE OF ORIGIN

Pièces en rapport avec les émissions de gaz d'échappement : KOMATSU ZENOAH AMERICA INC., parl'intermédiaire de n'importe quel revendeur

KOMATSU ZENOAH AMERICA INC.4344 Shackleford Road Suite 500Norcross, Georgia 30093© Printed in Japan

1. Parts location1. J-shape handle2. Ignition switch3. Throttle cable4. Throttle lever5. Throttle set button6. Blade guard7. Blade8. Wheel9. Spark arr

2. Specifications HEZ2500SOverall size(LxWxH)······················································ 71.9(1825)x15.4(390)x21.3(540) in(mm)Dry weight w

❲6❳3. Warning labels on the machine(1) Read owner's manual before operating this machine.(2) Wear head, eye and ear protection.(3) Warning/Attent

❲7❳For safe operation and maintenance, symbols arecarved in relief on the machine. According to theseindications, please be careful not to take a mist

❲8❳5. For safe operation1. Read this manual carefully until youcompletely understand and follow all safetyand operating instructions. 2. Keep this man

b. At night, at times of heavy fog, or at any othertimes when your field of vision might belimited and it would be difficult to gain a clearview of th