Redmax BCZ2600SU Bedienungsanleitung

BCZ2600SBCZ2600SUBCZ2600SWOWNER/OPERATOR MANUALBRUSHCUTTERS848-B50-93A1 (501)The engine exhaust from this productcontains chemicals known to the State

 10 • IF SOMEONE COMES1. Guard against hazardous situations at all times.Warn adults to keep pets and children awayfrom the area. Be careful if you

5. For safe operationrefill the tank of the unit in any place where thereis a boiler, stove, wood fire, electrical sparks,welding sparks, or any other

 12  MOUNTING ENGINE (SE1)1. Push the driveshaft housing toward the clutchhousing and rotate it by hand to check that thedriveshaft is engaged with

6. Set up (BCZ2600SW) MOUNTING ENGINE (SE5)1. Push the driveshaft housing toward the clutchhousing and rotate it by hand to check that thedriveshaft

 14 6. Set upSE10SE11 INSTALLING CUTTING HEAD (SE10)1. While locking the gear shaft, by inserting thesupplied tool into the upper holder on the gea

7. Fuel RECOMMENDED MIXING RATIOGASOLINE 50:OIL 1• Exhaust emission are controlled by thefundamental engine parameters andcomponents(eq., carburation

 16 7. Fuelagain for at least one minute. As someoils may be difficult to agitate dependingon oil ingredients, sufficient agitation isnecessary for

STARTING ENGINEThe cutting head will start rotating upon theengine starts.1. Rest the unit on a flat, firm place. Keep thecutting head off the groun

 18 8. Operation STOPPING ENGINE (OP3)1. Release the throttle lever and run the engine fora half minute.2. Shift the ignition switch to the STOP po

crowding the line into the cutting area. Allow theunit to trim at its own pace.1. Hold the unit so the head is off the ground and istilted about 20 de

SAFETY FIRSTInstructions contained in warnings within thismanual marked with a symbol concerncritical points which must be taken intoconsideration to

 20 9. Maintenance REFILLING TRIMMING LINE (MA1)1. For replacement line, use a diameter of .095in(2.4mm). The spool is capable for a line upto 20ft

on the housing, press the cap against thehousing until it clicks.•Make sure that the engine has stopped and iscool before performing any service to th

 22  MUFFLER• Inspect periodically, the muffler for loosefasteners, any damage or corrosion. If any signof exhaust leakage is found, stop using the

9. Maintenancethemselves to the brushcutter. Failing to doso could cause the muffler to becomeoverheated, and that this in turn could causethe engine

 24 10. Storage• Aged fuel is one of major causes of enginestarting failure. Before storing the unit, empty thefuel tank and run the engine until it

Under growthHeavy weedsLight weedsGrassNylon line headCUTTER APPLICATIONCHART9” 22-tooth:SST2299” 24-tooth:SST2498” 8-tooth:SGB0889” 8-tooth:SGB0898”

 26 11. Optional blade usage[ BCZ2600S, BCZ2600SU ]Change to the debris guard which is suitable forthe metal blade. (OPT3)130~174 in-lbs TIGHTENING

11. Optional blade usagespeed is too low, or the blade cuts too deep intoweeds. Adjust the engine speed and cuttingdepth according to the condition of

 28 you understand what causes kick out, how youcan reduce the chance of kick out and how youcan remain in control of the unit if kick out doesoccur

11. Optional blade usageOPT9 MAINTENANCEBLADE• Check the blade and the fasteners forlooseness, cracking, or bending.• Check the cutting edges and ref

2. Specifications BCZ2600S/BCZ2600SU/BCZ2600SWOverall size(LxWxH)BCZ2600S/BCZ2600SU ····································· 70.5(1790)x9.8(250)x12.2(31

12. Troubleshooting guideCase 1. Starting failure CHECK PROBABLE CAUSES ACTIONfuel tank ➞ incorrect fuel ➞ drain it and with correct fuelfuel filter ➞

13. Parts list NOTE : 1. Use KOMATSU ZENOAH genuine parts as specified in the parts list for repair and/orreplacement. 2. KOMATSU ZENOAH does not warr

13. Parts list  32 Fig.1 DRIVE UNIT BCZ2600S (S/N 300001 and up)BCZ2600SU (S/N 300001 and up)

101 9” 22-tooth SST229 1102 9” 24-tooth SST249 1103 8” 8-tooth SGB088 1104 9” 8-tooth SGB089 1105 8” 4-tooth SGB048 1106 9” 4-tooth SGB049 1107 GUARD

13. Parts list  34 Fig.2 DRIVE UNIT BCZ2600SW (S/N 300001 and up)

101 9” 22-tooth SST229 1102 9” 24-tooth SST249 1103 8” 8-tooth SGB088 1104 9” 8-tooth SGB089 1105 8” 4-tooth SGB048 1106 9” 4-tooth SGB049 1107 COVER

Fig.3 ENGINE UNITBCZ2600S (S/N 50100000 and up)BCZ2600SU (S/N 50100000 and up)BCZ2600SW (S/N 50100000 and up) 36 13. Parts list

 37 Key# Description Part Number Q'ty1 CYLINDER 4810-12111 12 GASKET, base 4810-12210 13BOLT, M5x22 1850-12130 24 INSULATOR 4810-13162 15 GASKE

EMISSION-RELATED PARTS, FOR TWO (2) YEARS FROM THE DATE OF ORIGINAL DELIVERY OF THE UNIT, KOMATSU ZENOAH AMERICA INC. (THE COMPANY), THROUGH ANY RedMa

Pièces en rapport avec les émissions de gaz d'échappement : KOMATSU ZENOAH AMERICA INC., parl'intermédiaire de n'importe quel revendeur

 4 (1) Read owner's manual before operating this machine.(2) Wear head, eye and ear protection.(3) Warning/Attention(4) Keep all children, byst

KOMATSU ZENOAH AMERICA INC.4344 Shackleford Road Suite 500Norcross, Georgia 30093© Printed in U.S.A.

For safe operation and maintenance,symbols are carved in relief on the machine.According to these indications, please becareful not to take a mistake.

 6 5. For safe operation1. Read this manual carefully until youcompletely understand and follow all safetyand operating instructions. 2. Keep this m

b. At night, at times of heavy fog, or at any othertimes when your field of vision might belimited and it would be difficult to gain a clearview of th

 8  BEFORE STARTING THE ENGINE1. The area within a perimeter of 50 feet (15m) ofthe person using the product should beconsidered a hazardous area i

Never place the throttle into the high speedposition when starting the engine.3. After starting the engine, check to make surethat the cutting attachm