RedMax EXtreme EX-LRT Anleitung zur Fehlerbehebung PDF herunterladen (Seite 78)

Oracle SBC Security Guide

Session Agent 192.168.60.10() [In Service]

-- Period -- -------- Lifetime --------

Active High Total Total PerMax High

Inbound Sessions 0 0 0 0 0 0

Rate Exceeded - - 0 0 0 -

Num Exceeded - - 0 0 0 -

Burst Rate 0 0 0 0 0 0

Reg Rate Exceeded - 7 21 21 21 21

Reg Burst Rate 0 0 0 0 0 0

Outbound Sessions 9000 9003 2452 14251475 1501 9009

Rate Exceeded - - 0 0 0 -

Num Exceeded - - 0 0 0 -

Burst Rate 0 50 0 0 0 51

Reg Rate Exceeded - - 0 0 0 -

Local Contacts 0 0 0 0 0 0

HNT Entries 0 0 0 0 0 0

Non-HNT Entries 0 0 0 0 0 0

Subscriptions 0 0 0 0 0 0

Out of Service - - 0 3 1 -

Trans Timeout 0 0 0 44 1 40

Requests Sent - - 17666 100035216 10906 -

Requests Complete - - 17671 100035175 10905 -

Seizure - - 2456 14251479 1501 -

Answer - - 2456 14250766 1502 -

ASR Exceeded - - 0 0 0 -

Messages Received - - 22595 128521055 13904 -

Latency=0.002; max=0.033

Message Rejections

Since release S-C(X)6.2.0 a new action type called reject is available to all header manipulation rules.

When this action type is used, and a condition matching the manipulation rule arises, the SBC rejects the

request, provides a SIP error, and increments a counter.

 If the msg-type parameter is set to any and the message is a response, the SBC increments a

counter to show the intention to reject the message—but the message will continue to be

processed.

 If the msg-type parameter is set to any and the message is a request, the SBC performs the

rejection and increments the counter.

The header manipulation rule -> new-value parameter is designed to supply the status code and reason

phrase corresponding to the reject. The following syntax is used to supply this information: status-

code[:reason-phrase] . The status-code and reason phrase information is not required since by default the

system uses 400:Bad Request.

If this information is not supplied, the status code must be a positive integer between 300 and 699. With

this defined, the SBC will use the applicable reason phrase corresponding to the status code in responses.

To customize the reason phrase, enter the status code followed by a colon (:). NOTE: be sure to enclose

the entire entry in quotation marks (ex: “400:Go Away” ) if the reason phrase includes spaces.

When the SBC performs the reject action, the current SIP manipulation stops processing and does not act

on any of the rules following the reject rule. This course of action is also true for nested SIP

manipulations that might have been constructed using the sip-manip action type. Keeping that in mind,

the reject rule is usually the last rule in a long HMR.

1 2 ... 73 74 75 76 77 78 79 80 81 82 83 ... 141 142

Kommentare zu diesen Handbüchern

Keine Kommentare

RedMax EXtreme EX-LRT Anleitung zur Fehlerbehebung Seite 78

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Grasschneider RedMax EXtreme EX-LRT